provision-ap copy-provisioning-params ap-name "6c:f3:7f:c6:7e:a6"
provision-ap installation default
provision-ap no external-antenna
provision-ap no usb-dev
provision-ap no usb-dial
provision-ap no usb-init
provision-ap no usb-modeswitch
provision-ap no usb-passwd
provision-ap no usb-tty
provision-ap no usb-type
provision-ap no usb-user
provision-ap master 10.215.200.191
provision-ap server-ip 10.215.200.191
provision-ap ap-group "TK-11ac"
provision-ap ap-name "AP-225-3"
provision-ap no syslocation
provision-ap remote-ap
provision-ap reprovision ap-name "6c:f3:7f:c6:7e:a6"
---
(Aruba3600) (AP provisioning) #?
a-ant-bearing Bearing for 5.2GHz (802.11a) antenna in decimal
degrees from True North. Range: 0-360.
a-ant-gain Gain for 5.2GHz (802.11a) antenna
a-ant-tilt-angle Tilt angle for 5.2GHz (802.11a) antenna in decimal
degrees. -ve for downtilt, +ve for uptilt. Range:
-90 to +90.
a-antenna Antenna to use for 802.11a (5GHz) (1, 2, or both)
altitude Altitude of the AP in decimal format.
ap-group The AP group of the AP
ap-name The name of the AP
apdot1x-passwd Password of AP so that AP can authenticate to 802.1x
using PEAP
apdot1x-username The username of the AP so that the AP can
authenticate to 802.1x networks using PEAP
cellular_nw_preference Multimode cellular modem network preference type
copy-provisioning-par.. Copy a provisioning-ap-list entry to
provisioning-params
dns-server-ip The IP address of the AP's DNS server
dns-server-ip6 The IPv6 address of the AP's DNS server
domain-name The DNS domain name of the AP
external-antenna Use external antenna
fqln Fully qualified location name
g-ant-bearing Bearing for 2.4GHz (802.11g) antenna in decimal
degrees from True North. Range: 0-360.
g-ant-gain Gain for 2.4GHz (802.11g) antenna
g-ant-tilt-angle Tilt angle for 2.4GHz (802.11g) antenna in decimal
degrees. -ve for downtilt, +ve for uptilt. Range:
-90 to +90.
g-antenna Antenna to use for 802.11g (2.4GHz) (1, 2, or both)
gateway The default gateway IP address for the AP
gateway6 The default gateway IPv6 address for the AP
ikepsk The IKE pre-shared key
installation The type of installation (Indoor or Outdoor)
ip6addr The static IP6 address of the AP
ip6prefix The prefix of static IPv6 address of the AP
ipaddr The static IP address of the AP
latitude Latitude of the AP in DMS (Degrees,Minutes,Seconds)
format. Example: "37 22 08.75 N" (DDD MM SS.SS D)
link-priority-cellular Priority of cellular link [0=min; 255=max]
link-priority-ethernet Priority of ethernet link [0=min; 255=max]
longitude Longitude of the AP in DMS (Degrees,Minutes,Seconds)
format. Example: "122 02 34.29 W" (DDD MM SS.SS D)
master The DNS name or IP address of the AP's switch
mesh-role The role of the AP in mesh network (Mesh Point or
Portal)
mesh-sae Enable or Disable SAE on Mesh network (Default
Disable)
netmask The netmask associated with the static IP address of
the AP
no Delete Command
pap-passwd The PAP password configured on the switch for the AP
(6-32 characters)
pap-user The PAP username configured on the switch for the AP
pkcs12-passphrase PKCS12 PASSPHRASE
pppoe-chap-secret The CHAP secret key used for CHAP authentication.
Max 50 characters in length.
pppoe-passwd The PAP password configured on the PPPoE Access
Concentrator for the AP
pppoe-service-name The PPPoE service name
pppoe-user The PAP username configured on the PPPoE Access
Concentrator for the AP
read-bootinfo Read current Boot Environment in AP
remote-ap This is a remote AP
reprovision Send current provisioning-params to AP(s)
reset-bootinfo Restore factory default boot variables
sch-mode-radio-0 Single chain mode for Radio 0 (Enable/Disable)
sch-mode-radio-1 Single chain mode for Radio 1(Enable/Disable)
server-ip The IP address of the switch containing the AP image
server-name The DNS name of the switch containing the AP image
set-ikepsk-by-addr Set IKE PSK corresponding to a given IP address.
syslocation SNMP sysLocation
uplink-vlan AP sends/receives frames tagged with this VLAN on
its Ethernet uplink
usb-dev The USB device identifier, if device is not already
supported
usb-dial The dial string for the USB modem, if default is
incorrect
usb-init The initialization string for the USB modem, if
default is incorrect
usb-modeswitch ALL the parameters that is required to be passed to
usb_modeswitch utility
usb-passwd The possibly optional PPP password provided by the
cellular service provider
usb-power-mode Choose USB power mode [auto; enable; disable]
usb-tty The TTY device data path for the USB modem, if
default is incorrect
usb-tty-control The TTY device control path for the USB modem, if
default is incorrect
usb-type The USB driver type, for any 3G/2G USB modems
usb-user The PPP username provided by the cellular service
provider
0 件のコメント:
コメントを投稿